A few things you should know about mandalorian beskar armor costume

 Helmet

Flight Suit

• The suit is made of brown cotton canvas, with white stitching forming the lines
• Two-piece construction
• The Flight Suit has double sleeves
• There are extra thin threads sewn on the corresponding parts of the suit to fix the armor

Flak Vest (vest under the breastplate)

• The vest is made the same material as the flight suit
• Zipper in the middle
• There is velcro on the vest to fix the cloak, and thin lines on the chest to fix the breastplate

Cummerbund

• Use light brown cotton canvas
• Topstitching is dark color
• Use Velcro to adjust
• Abdominal Tasset is Blue, made of PU

• Cummerbund &Tasset are connected together and cannot be separated

Gloves

• (Hand Plates)The armor of both hands is white, with a blue triangle in the middle, mainly made of resin, and directly mounted on the back of the glove
• The glove is black, mainly made of PU leather, without fingers; there is an elastic band on the inside of the wrist, which can be adjusted by velcro
• Yellow gloves mainly cut with fabric and used with black gloves

Cape:

• Gray, mainly using velvet(100% polyester) for cutting and sewing
• Cape covers the shoulders and is wide enough to bunch up across the back and shoulders.
• Four pleated sections on the left side of the cape and covered with fabric extending from the right side.
• Can direct pull-over
• There are velcro on the inside of the cape, which corresponds to the position of the velcro on the vest

Shoulder Armor

• Silver appearance, mainly made of Fiberglass mix resin
• Both shoulders are symmetrical.
• Armor is symmetrical with a tall vertical raised ridge from top to bottom
• The Mudhorn signet is present on right shoulder armor
• There are small rings on the inside of the armor, which corresponds to the position of the thin line on the suit

Chest Armor

• Silver appearance, mainly made of Fiberglass mix resin
• Armor is a two-part construction.To prevent falling off, use an elastic band on the inner side of the breastplate to connect the upper plate and the lower plate to make it integrated
• Recessed strip features a 6 sided debossed diamond detail.
• Some small rings on the inside of the armor

Left Gauntlet

• Silver appearance, mainly made of Fiberglass mix resin
• The top of the gauntlet is flat with a launcher detail and two rectangular profiles on either side.
• Launcher is comprised of a half-cylinder detail featuring ribs, the front of the half-cylinder features a cone with 12 holes.(If you want to install light-emitting parts, you can modify the gauntlet yourself)
• The gauntlet is divided into two parts, which are connected by an elastic rope, which can be flexibly extended and retracted, which is convenient to adjust the size, making the handguard more suitable for the arm
• A total of 20 buttons with keyboard-like buttons printed on the bottom of the front of the gauntlet. (The center 3 buttons of each row of the keypad are slightly larger than the outside buttons.)

Right Gauntlet

• Silver appearance, mainly made of Fiberglass mix resin
• The gauntlet is divided into two parts (same as left gauntlet)
• The top of the gauntlet consists of a raised rectangle with angled edges and a narrow rectangular detail on top.
• Outer face features protruding profile near the top edge with 5 grooves.
• The top edge near the wearer's elbow features a none display (If you want to equip a red-tinted electronic display, you need to modify it yourself)

Tasset Armor

• Blue with white thread, made of PU leather
• Hang on the belt of the trousers, located on both sides of the legs Left Thigh Armor

Right Thigh Armor

• Dark green appearance, mainly made of Fiberglass mix resin
• Armor features a raised rectangular edge.
• A vertical raised ridge from top to bottom
• Some small rings on the inside of the armor

Right Thigh Armor

• Silver appearance, mainly made of Fiberglass mix resin
• Armor features a raised rectangular edge.
• Armor features a raised rectangular ridge in the center that merges into the top & bottom edge.
• Some small rings on the inside of the armor

Knee armor

• Dark Blue appearance, mainly made of Fiberglass mix resin
• Armor flares outward at the back of the knee on each side.
• Two silver darts are attached on the outside of the knee and are solid
• Armor secured by a black strap
• A rectangular trapezoidal detail is present with a visible groove inside the perimeter of the outer face
• Because the pants are thin and there is no cushion on the inner side of the knee armor, it is recommended to wear the armor after wearing the knee protector at the knee

Leg Greave 

• The calf armor is divided into left and right, mainly made of PU leather and fabric
• The inner side is fixed with an elastic band, all accessories are stitched together in advance, only the resin bullet of the right calf armor needs to be worn by yourself

Belt

• Belt buckle is metal/metal looking material, belt mainly made of PU leather
• From buckle to the left the belt features; Ammo belt(front), gun holster, ammo belt(back), 3 breach charges & PU leather pouch, sidearm holster.
• 4 resin bullets can be placed on the belt

Bandolier(front)

• Mainly made of PU leather
• There is a metal buckle at one end to adjust the length of the bandolier, and the other end can be fixed through the belt

Bandolier(back)

• Mainly made of PU leather
• There is a metal buckle at one end to adjust the length of the bandolier, and the other end can be fixed through the belt

Gun Holster

• Mainly made of PU leather, can put on a weapon
• One end can be fixed through the belt

Sidearm Holster

• Mainly made of PU leather,
• Back part can be fixed through the belt

3 Grav Charges & PU Leather Pouch

• 3 Grav Charges are one-piece
• Breach charge holder is metal/metal-like in appearance, color is slive, Breach charges have a red lens that is slightly domed (can not shine)
• The lower part of the breach charge holder is wrapped in PU leather pouch